Repiping & Pipe Replacement Across DFW

Whole-Home Repiping & Pipe Replacement in Dallas–Fort Worth

Third pinhole leak this year? Rusty water first thing in the morning? Gray plastic pipe stamped PB2110 in the attic? Finish Line MEP handles whole home repiping and targeted pipe replacement for houses and commercial buildings across the Metroplex. We find out what your pipes are made of, tell you plainly whether repiping is the right call, and price the job before a single wall is opened.

Schedule a Repipe Estimate

Request Service

Tell us what’s going on and we’ll call you back. Need help now? Call us 24/7.

Repiping in DFW

Whole Home Repiping: When It Beats Another Leak Repair

A single leak is a repair. A pattern of leaks is a message about the pipe itself. Once a home’s supply piping has started failing from the inside out, through corrosion, chemical breakdown or decades of wear, patching one spot just moves the next failure somewhere else. Home repiping replaces the hot and cold supply lines as a system, so you stop paying for the same problem one section at a time.

Not every house needs the whole thing. Plenty of DFW homes have one bad run, a failed branch under the slab, or a short stretch of galvanized left over from an old remodel. Partial re-piping and targeted pipe replacement are part of what we do, and we will tell you when a full repipe is more than the house needs. Where water pipes run through the slab, rerouting the line overhead through the attic or walls is often cleaner than breaking concrete. Call for an appointment or fill out the quick form at the top of this page, and we will show you on site which way makes sense for your house.

Our work covers single-family homes, rentals, and commercial buildings. North Texas adds its own wrinkles: expansive clay that moves slabs and the pipes in them, chloraminated city water that is hard on some rubber parts, and attic runs exposed to both summer heat and the occasional hard freeze. We plan the new layout around all of it.

Every repipe is permitted where the city requires it, pressure-tested before walls are closed, and reconnected to your fixtures, shutoffs and water heater so the house works the day we finish.

What’s Included in Repiping & Pipe Replacement

Pipe Assessment & Scope

We identify every material in the system, trace where the failures are coming from, and check pressure and the main shutoff. You get a written scope: whole house, one branch, or a repair that buys real time.

PEX Repipe

Flexible PEX runs long distances with few fittings, holds up well to chloraminated water, and tolerates a freeze better than rigid pipe. It is the most common choice for a whole-home repipe and usually the least disruptive to install.

Copper Repipe

Type L copper remains a solid choice for owners who want rigid metal pipe. We size it correctly, support it properly, and keep it off direct contact with dissimilar metals so it is not set up for pinhole leaks.

Polybutylene & Galvanized Pipe Replacement

Polybutylene replacement removes a material that was installed in up to 10 million U.S. homes before production stopped in 1995. Galvanized pipe replacement ends the rust, scale and slow pressure loss of steel lines that are corroding from the inside.

Partial Repipes & Slab Reroutes

One failed branch, an addition tied into old pipe, or a line under the slab that keeps leaking. We replace the section that is actually the problem, and reroute supply lines overhead when that beats opening the foundation.

Commercial Repipe

Domestic water, risers and cast iron drain lines in offices, retail, warehouses and multifamily buildings, phased around tenants and business hours. Call to set up a walk-through of your building.

Know the Warning Signs

Signs It May Be Time to Repipe

One of these on its own may only need a repair. Two or three together usually point to the pipe itself.

1

Pinhole leaks in different places

Small leaks showing up in different spots, often in copper lines.

2

Brown or rusty water

Discolored water, especially after the house sits overnight.

3

Pressure that keeps dropping

Pressure that has dropped over the years at every fixture, a classic sign of galvanized pipe closing up inside.

4

PB2110 stamped on the pipe

Gray, blue or black flexible plastic supply pipe stamped PB2110 (polybutylene).

5

Repeat slab leaks

A second or third slab leak in the same home.

6

Corrosion at fittings

Visible green or white corrosion at fittings and valves.

Seeing more than one of these? Call for an appointment or use the quick form at the top of this page, and we will tell you whether it is a repair or a repipe.

Repipe Cost Factors

Size and layout: number of bathrooms, fixture count, and one story or two.

Material: a PEX repipe generally costs less than a copper repipe.

Access: open attic and chases versus tight crawl space, finished ceilings or slab routing.

Scope: whole house, one branch, or supply plus fixture valves and water heater connections.

Finishes: how much drywall patching and texture matching the job needs.

Repipes run from a few thousand dollars for a partial job to well into five figures for a large home. Every job is priced after we see it.

Why DFW Owners Choose Finish Line MEP for Repiping

A repipe is a big decision and most people only make it once. We earn it by being straight about whether you need one, careful inside your home, and clear about the price.

Honest Repair-or-Repipe Advice

If a single repair will hold, we say so. If the pipe is failing as a system, we show you why, with the leak history, the material and the corrosion in hand.

Priced Before We Start

You get a written scope and a price before work begins, covering the piping, the access openings and the patching, so there is no surprise at the end.

Clean, Protected Job Sites

Floor protection, dust control and small planned openings. Water is back on at the end of each working day wherever the layout allows it.

Residential and Commercial Crews

Licensed plumbers based in Grapevine who repipe single-family homes, rentals and occupied commercial buildings across Dallas, Fort Worth and the suburbs.

Related Services

Home repiping in LewisvilleCommercial cast iron repipe projectSigns an Arlington business needs a repipeSlab leak repairWater line repair and replacement

Repiping FAQs

How long does whole home repiping take?

Most single-family homes take a few working days from first cut to final pressure test, longer for large two-story homes or copper. Water is usually off only during the working day while we switch fixtures over to the new lines, so most families stay in the house. Drywall patching follows once the new piping passes its test.

Is a PEX repipe or a copper repipe better?

Both are good, code-approved choices. PEX costs less, needs fewer fittings, and handles chloraminated water and freezes well. Copper is rigid, long-proven and preferred by some owners, but it costs more and can develop pinholes in some water conditions. We will recommend one based on your house, not on what is easiest for us.

How much does it cost to repipe a house in DFW?

A partial repipe can be a few thousand dollars; a whole-home repipe on a large house can run well into five figures. Size, number of bathrooms, PEX or copper, access to the attic and walls, and how much drywall repair is needed all move the price. Every job is priced after we see it.

Do you have to tear out walls to repipe a house?

Some openings are unavoidable, but they are small and planned. PEX can be fished through walls and ceilings from the attic, so most repipes need a series of small access holes at fixtures rather than whole walls removed. We protect floors and furnishings, and patch the openings when the work is done.

Should I replace polybutylene pipe if it is not leaking yet?

Usually, yes. Polybutylene tends to fail from the inside without visible warning, and when it lets go it often fails suddenly. Many insurers and buyers also treat it as a known risk. Replacing it on your schedule is cheaper and calmer than replacing it after a burst.

Do you repipe commercial buildings?

Yes. We repipe domestic water lines, risers and cast iron drain and vent systems in offices, retail, warehouses and multifamily buildings. Work is phased by floor, unit or zone so tenants keep water and the building keeps running.

Still deciding between a repair and a repipe? Call for an appointment or fill out the quick form at the top of this page and we will come look at the pipes with you.

Get in Touch

Stop Repairing the Same Pipes Twice

Whether it is polybutylene in the attic, galvanized that has choked down the pressure, or copper that keeps springing pinholes, Finish Line MEP will tell you what is really going on and what it takes to fix it for good. Repiping and pipe replacement for homes and commercial buildings across Dallas–Fort Worth, priced before we start.